Finally, I found some time to install a 240V line in my shack. It was a bit challenging because I had no available breaker positions in my electrical panel (load center). The electrical panel was really crowded, all breakers were in use and and even separate circuits were sharing common breakers. There was no way that I can free 2 breaker positions for the 240V line so I decided to install a sub-panel. It was time to put on the electrician's hat ;-)
My existing electrical panel - power is supplied to the house by 2 hot wires (single phase) and a neutral wire (which is also grounded in the panel as per NEC) . These are the 3 black heavy wires in the middle of the picture. They are connected straight to the outside service (the electric pole transformer on the street). There are 120V between each hot wire and the neutral (common) wire and 240V across both hot wires. These lines are actually connected to the center-tapped 240V secondary winding of the power transformer outside. Each end of the winding is a "hot" wire and the center-tap is the common.
To install a sub-panel I needed first to install a double-pole breaker in the main panel to serve as a feeder (main) breaker for the sub-panel and bring this way the outside service to the sub-panel thru the double-pole breaker in the main panel.
Piece of plywood was installed next to the existing panel. I used Tapcon screws to attach it to the concrete wall. BTW I did not install the main panel - judging by the angle, whoever did - was obviously drinking at the time :-)
Here is the new sub-panel, attached to the plywood. I installed 8 (16) position 125 Amps sub-panel. This should cover all my future needs. The double-pole 100 Amp breaker is installed at top-right in the main panel. Three AWG #4 stranded copper wires serve as feeder for the sub-panel. Wire size #4 should be able to handle up to 125 Amps (something very unlikely to occur). The green wire (AWG #6) is used to connect sub-panel's Ground to the main panel.
This picture shows the finished sub-panel. I moved some circuits from the main panel including those which I had to disconnect to make room for the sub-panel feeder breaker. I installed also a 20A utility receptacle under the sub-panel. The yellow wire (3- AWG#12) is the 240V line. It is connected to a double-pole 20A breaker at top-left. Safety reasons require the use of a double-pole instead of two single-pole breakers. When using a double-pole breakers, both hot wires will be disconnected even only one is overloaded. (Same reason to use double-pole breakers at the sub-panel feeder line)
This is the 30A in-line RFI filter - Corcom 30VB6. This AC filter is rated at 25A/240V or 30A/120V and provides pretty good attenuation throughout the HF range. The insertion loss is over 50db at 30 MHz. I have similar filters on the line powering the rest of the shack and on the line powering all of my computers. This means that the insertion loss is over 100 db between devices from each group.
To accommodate the filter I used electrical box from a "pull-to-disconnect" device sold for Air Conditioners. It accommodates perfectly the EMI filter and provides the necessary high-voltage safety.
My new 240V/20A AC line is finally operational! As it turns out - I can use it as AC voltage reference :-))
2 comments:
I noticed that in your sub feed, you have the two hot wires inside one piece of smurf tube and the neutral+ground in another piece. That might be a violation of national and/or local electric code.
yes..I am aware that using two conduits is a NEC violation and I intend to fix it at some point. Not for any other reasons but to make the inspector happy next time he pays me a visit.
A couple of points tho: The sub-panel is serving my 240V HF amp and I hope you are as familiar with 240V service as you are with NEC - there is NO NEUTRAL and BOTH lines are HOT when using 240V. Both hot lines are actually the secondary winding of the center- tapped distribution transformer. The center tap is grounded and it is the neutral as well. Each half - between the end and the center-tap is one of the two 120V circuits (single split-phase). In a typical household wiring, different loads are connected to different halves of the transformer windings and an attempt is made to distribute the loads evenly across both circuits. In practice this is never the case - one load (the refrigerator for instance) will be operating for a period of time loading one half of the winding more than the other. What is humorous is to think that you are dealing with balanced transformer or even balanced panel, feed, etc. Furthermore, you are talking about common-mode currents/noise caused by different return paths (ground and hot) and asymmetry in the feeder, while the EMI filter is intended to deal with differential-mode noise between the two hot wires (caused by other loads).
In addition, the length of each wire to the sub-panel is the same and very short! The proximity between the wires over this short distance is such that it is humorous to me that someone might think the two plastic conduits are affecting the twisted-pair effect.
btw. when was the last time when you looked at a pole transformer and the wires of the utility drop. According to your logic the difference in the length of the wires and lack of symmetry and neat bundles (observed on pretty much every utility pole) should turn them into some serious EMI sources (afterall the magnetic fields failing to "cancel out" are the result of the combined load of a few households)
Finally, I have absolutely clean sine-wave on my scope and no traces of noise after the filter. Another proof is the absolutely clean output of the amplifier with no harmonics splatter and no distortion whatsoever
Post a Comment